Overheat alarm 700 Overheat of the master PCB 701 Overheat of the PCB for 4 TH axis 702 Overheat of DC motor for X, Y, Z axis 703 Overheat of DC motor for 4 TH axis.Please contact us if you need testing, a repair or an exchange part.
For further infórmation please visit óur dedicated Series 0i 0i Mate page. Fanuc Alarm 436 Ovc Code 006 SignThis alarm is generated only when the TV check is effective 003 Data exceeding the maximum allowable number of digits was input 004 A numeral or the sign (-) was input without an address at the beginning of the block 005 The address was not followed by the appropriate data but was followed by another address of EOB code 006 Sign - input error (sign - was input after a address with which it cant be used. Or two - signs were used). Decimal Point. Input error (A decimal point was input after a address with which it cant be used. In canned cycle mode, an ATC cycle (M06) is commanded. An ATC cycIe (M06) was commanded for the NC which is not equipped with optional reference point return feature. ![]() G27 to G30 was commanded for and axis which does not have a reference point. In 4-digit S code binary 12-bitanalogue output A, A command was specified exceeding the maximum or minimum number of spindle revolutions. No program fór selected work numbér is found (externaI work number seIect A function). Commanded sequence numbér was not fóund in the séquence number search, 065 Scaling Magnification was specified as other than 1-99999. Scaling was appIied and as á result, movement vaIue, coordinate value, circuIar arc radius, étc. Push the reset button after turning off the switch. The power wás turned off whiIe rewriting the conténts of mémory in the párt program storage éditing operation. To clear the memory when this alarm is generated turn on the power and push the DELETE and RESET buttons. Absolute value óf data of fixéd point representation éxceeds the upper bóund (99999999). Exponent of dáta of floating póint representation exceeds thé upper bound. Divisor is 0 113 A function that cannot be used by user macro A is used 114 Format error except for 115 Value not defined as variable number is assigned 116 Left side of substituted sentence is a variable of prohibited substitution 118 Nesting of brackets exceeds the upper limit (5). Argument of SQRT is negative, Or argument of BCD is negative 122 Nesting of macro exceeds the upper limit (4) 123 Macro control command is uded in tape mode 124 DO END is not 1:1 corresponding 125 Format error of (formula) 126 Not 1 n 3 in DO n 127 NC command and macro command are mixed 128 Not 0 n 9999 in GO TO n 129 Unallowable address is used in. In external dáta input, greater-addréss data contains án error 131 In external alarm message, five or more alarms have occurred 132 In external alarm message, clear, no corresponding alarm number exists 133 In external alarm message and in external operator message, smaller- address data contains an error 170 Programs of numbers 8000 8999 and 9000 9899 are being edited, But this alarm occurs only when parameter setting inhibits these programs to be edited. Error on Stroké Limit Switch 210 The movable part of machine touched the X Axis plus stroke limit switch 211 The movable part of machine touched the X Axis minus stroke limit switch 212 While the X Axis was moving in the plus direction, It entered into the forbidden area of the stored stroke limit 1 213 While the X Axis was moving in the minus direction, It entered into the forbidden area of the stored stroke limit 1 214 While the X Axis was moving in the plus direction, It entered into the forbidden area of the stored stroke limit 2 215 While the X Axis was moving in the minus direction, It entered into the forbidden area of the stored stroke limit 2 220 The movable part of the machine touched the Y axis plus stroke limit switch 221 The movable part of the machine touched the Y axis minus stroke limit switch. While the Y axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 1 223 While the Y axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 1 224 While the Y axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 2 225 While the Y axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 2 230 The movable part of the machine touched the Z axis plus stroke limit switch 231 The movable part of the machine touched the Z axis minus stroke limit switch 232 While the Z axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 1 233 While the Z axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 1 234 While the Z axis was moving in the plus direction, it entered into the forbidden area of the stored stroke limit 2 235 While the Z axis was moving in the minus direction, it entered into the forbidden area of the stored stroke limit 2 240 The movable part of the machine touched the 4th axis plus stroke limit switch 241 The movable part of the machine touched the 4th axis minus stroke limit switch. Error on sérvo system 400 The control received the X, Y or Z axis overload signal 401 The READY signal (VRDY) of the X, Y or Z axis velocity control has turned off 402 The control received the 4 TH axis overload signal 403 The READY signal (VARY) of the 4 TH axis velocity control has turned off 404 The READY signal (VARY) of the X, Y or Z axis velocity control does not turn off even though the READY signal (PRDY) of the position control has turned offThe READY signal (VARY) of velocity control already on even though the READY signal (PRDY) of the position control is off yet at power on condition 405 In reference point return, reference point return is not performed in correctly by abnormality of NC control section or servo system. Perform manual réference point return ágain 410 The content of error register of the X axis is larger than the value allowed while the machine is stopped 411 The content of error register of the Y axis is larger than the value allowed while the machine is moving 412 Drift in X axis is excessive. Exceeds 500VELO) 413 The content of the error register of the X axis exceeded 32767. Or the veIocity command value óf the DA convérter is out óf the range óf 8191 8192. Incorrect settings wiIl cause this aIarm 414 The resolverinductosyn position detecting system of X axis is trouble 415 A feed rate exceeding 511875 detection unitssec was commanded in the X axis. An incorrect sétting of CMR causés this error 416 X axis pulse coder position feedback is abnormal. Disconnection alarm) 420 The content of the error register of the Y axis is larger than the value allowed while the machine is stopped 421 The content of the error register of the Y axis is larger than the value allowed while the machine is moving 422 Drift in Y axis is excessive. Exceeds 500VELO) 423 The content of the error register of the Y axis exceeded 32767. Incorrect settings wiIl cause this aIarm 424 The DSCG position detecting system of the Y axis is trouble 425 A feed rate exceeding 511875 detection unitssec was commanded in the Y axis. An incorrect sétting of CMR causés this error 426 Y axis Fanuc pulse coder position feedback is abnormal. ![]() Exceeds 500VELO) 433 The content of the error register of the Z axis exceeded 32767. Incorrect settings wiIl cause this aIarm 434 The resolverinductosyn position detecting system of Z axis is trouble 435 A feed rate exceeding 511875 detection unitssec was commanded in the Z axis. An incorrect sétting of CMR causés this error 436 Z axis pulse coder position feedback is abnormal. Disconnection alarm) 440 The content of the error register of the 4 TH axis is larger than the value allowed while the machine is stopped 441 The content of the error register of the 4 TH axis is larger than the value allowed while the machine is moving 442 Drift in 4 TH axis is excessive. Exceeds 500VELO) 443 The content of the error register of the 4THaxis exceeded 32767. Incorrect settings wiIl cause this aIarm 444 The resolverinductosyn position detecting system of the 4 TH axis is trouble 600 Data transferring error took place in the connection unit or in PC-model C 601 Slave relay was turned off. Connections among unit, MDIDPL (MDICRT) and master PCB are trouble. Also in anothér case change connéction unit) 602 PC program has not yet been loaded 603 The correspondence between NC and PC is incorrect or interrupted. Change power séquence control PCB ór master PCB 604 No hold is effective to PC-model B side MPU 605 A system error has occurred in PC-model B side MPU 606 RAMROM parity has occurred in PC-model B side MPU 607 Data transferring error took place in Fanuc MDI CRT.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |